manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 55 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 55

Chapter 1 About Ethernet Switches 325 and 425

55

System Configuration Guide

 

•

RFC 1573 (Interface MIB)

•

RFC 1643 (Ethernet MIB)

•

RFC 1757 (RMON)

•

RFC 1271 (RMON)

•

RFC 1157 (SNMP)

Standards

The following IEEE Standards also contain information germane to the Ethernet 
Switch 325/425:

•

IEEE 802.1D (Standard for Spanning Tree Protocol)

•

IEEE 802.3 (Ethernet)

•

IEEE 802.1Q (VLAN Tagging)

BootP automatic IP configuration/MAC address

The Ethernet Switch 325/425 has a unique 48-bit hardware address, or MAC 
address, that is printed on a label on the back panel. You use this MAC address 
when you configure the network BootP server to recognize the Ethernet Switch 
425-24T BootP requests. A properly configured BootP server enables the switch 
to automatically learn its assigned IP address, subnet mask, IP address of the 
default router (default gateway), and software image file name.

For information about a stack MAC address, see 

“Stack MAC address” on 

page 89

.

For more information and an example of a BootP configuration file, see 

Appendix D, “Sample BootP configuration file,” on page 443

.

Configuration and switch management

The Ethernet Switch 325/425 that is shipped directly from the factory is ready to 
operate in any 10BASE-T or 100BASE-TX standard network.

You must assign an IP address to the switch or stack, depending on the mode of 
operation. You can set both addresses by using the console port or BootP, which 
resides on the switch. You can manage the switch using:

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов