Nortel 425-24T Скачать руководство пользователя страница 253

Страница: 253 / 488

Chapter 7 System configuration using the CLI

253

System Configuration Guide

Table 58

describes the parameters and variables for the

ip address

command.

no ip address command

The

ip address

command clears the IP address and subnet mask. This

command sets the IP address and subnet mask for a switch or a stack to all zeros
(0). The syntax for the

ip address

command is:

no ip address {stack|switch}

The

ip address

command is in the config command mode.

Table 59

describes the parameters and variables for the

ip address

command.

Table 58

ip address command parameters and variables

Parameters and
variables

Description

stack|switch

Sets the stack the IP address and subnet mask or the switch IP
address and netmask.

unit

Sets the IP address of another unit in a stack.

XXX.XXX.XXX.XXX Enter IP address in dotted decimal notation; netmask is optional.

netmask

Set the IP subnet mask for the stack or switch.

Note:

When you change the IP address or subnet mask, you may lose

connection to Telnet and the Web.

Table 59

no ip address command parameters and variables

Parameters and
variables

Description

stack|switch

Zeroes out the stack IP address and subnet mask for the switch IP
address and subnet mask.

unit

Sets the IP address of another unit in a stack.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 253 / 488

Результаты поиска

Содержание 425-24T

Отзывы: