manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 271 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 271

Chapter 7 System configuration using the CLI

271

System Configuration Guide

 

•

“show terminal command”

•

“terminal command” on page 271

show terminal command

The 

show terminal

 

command displays the current serial port information, 

which includes connection speed, as well as the terminal width and length in 
number of characters. The syntax for the 

show terminal

 command is:

show terminal

The 

show terminal

 

command is in the exec command mode.

The 

show terminal

 

command has no parameters or variables.

Figure 99

 shows the output from the 

show terminal

 

command.

Figure 99   

show terminal command output

terminal command

The 

terminal

 command configures the settings for the terminal. These settings 

are transmit and receive speeds, terminal length, and terminal width. The syntax 
of the 

terminal

 command is:

terminal speed {2400|4800|9600|19200|38400}|length 

<1-132>|width <1-132>

The 

terminal

 command is in the exec mode.

425-48T(config-if)#show terminal

Terminal speed: 9600

Terminal width: 79

Terminal length: 23

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов