Nortel 425-24T Скачать руководство пользователя страница 325

Страница: 325 / 488

Chapter 8 Ethernet port management using the CLI

325

System Configuration Guide

Table 112

describes the parameters and variables for the

default

speed

command.

duplex command

The

duplex

command specifies the duplex operation for a port. The syntax for

the

duplex

command is:

duplex [port <portlist>] {full|half|auto}

The

duplex

command is in the config-if command mode.

Table 113

describes the parameters and variables for the

duplex

command.

Table 112

default speed command parameters and variables

Parameters and
variables

Description

port <portlist>

Specifies the port numbers to set the speed to factory default.
Enter the port numbers you want to set.

Note:

If you omit this parameter, the system uses the port number

you specified in the

interface

command.

Table 113

duplex command parameters and variables

Parameters and
variables

Description

port <portlist>

Specifies the port number to configure the duplex mode. Enter the
port number you want to configure, or all to configure all ports
simultaneously.

Note:

If you omit this parameter, the system uses the port number

you specified in the

interface

command.

full|half|auto

Sets duplex to:

•

full—full-duplex mode

•

half—half-duplex mode

•

auto—autonegotiation

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 325 / 488

Результаты поиска

Содержание 425-24T

Отзывы: