manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 407 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 407

Chapter 13 Troubleshooting

407

System Configuration Guide

 

Port connection problems

You can usually trace port connection problems to either a poor cable connection 
or an improper connection of the port cables at either end of the link. To remedy 
these types of problems, make sure that the cable connections are secure and that 
the cables connect to the correct ports at both ends of the link.

Port connection problems are also traceable to the autonegotiation mode or the 
port interface.

Autonegotiation modes

Port connection problems can occur when a port (or station) is connected to 
another port (or station) that is not operating in a compatible mode (for example, 
connecting a full-duplex port on one station to a half-duplex port on another 
station).

The Ethernet Switch 325/425 negotiates port speeds according to the IEEE 802.3u 
autonegotiating standard. The switch adjusts (autonegotiates) its port speed and 
duplex mode to match the best service provided by the connected station, up to 
100 Mb/s in full-duplex mode as follows:

Table 155   

Corrective actions

Symptom

Probable cause

Corrective action

All LEDs are off.

The switch is not receiving AC 
power.

Verify that the AC power cord is fastened securely 
at both ends and that power is available at the AC 
power outlet.

The fans are not operating or 
the airflow is blocked, causing 
the unit to overheat.

Verify that there is sufficient space for adequate 
airflow on both sides of the switch.

Note:

 Operating temperature for the 

switch must not exceed 40°C (104°F). Do 
not place the switch in areas where it can 
be exposed to direct sunlight or near 
warm air exhausts or heaters.

The Activity LED for a 
connected port is off or 
does not blink (and you 
have reason to believe 
that traffic is present).

The switch is experiencing a 
port connection problem.

See 

“Port connection problems”

.

The switch’s link partner is not 
autonegotiating properly.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов