manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 348 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 348

348

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Figure 135   

Edit Chassis dialog box — Stack Info tab

Table 131

 describes the 

Stack Info 

tab fields.

Table 131   

Stack Info tab fields

Field

Description

Descr

A description of the component or subcomponent. If not available, the 
value is a zero length string.

Location

The geographic location of a component in a system modeled as a 
chassis, but possibly physically implemented with geographically 
separate devices connected together to exchange managment 
information. Chassis modeled in this manner are sometimes referred to 
as virtual chassis. An example value is: '4th flr wiring closet in blg A'. 

Note: 

1. This object is applicable only to components that can be found 

in either the Board or Unit groups. If the information is unavailable, for 
example, the chassis is not modeling a virtual chassis or component is 
not in Board or Unit group, the value is a zero length string. 

2. If this object is applicable and is not assigned a value through a SNMP 
SET PDU when the row is created, the value will default to the value of 
the object s5ChasComSerNum. 

LstChng

The value of sysUpTime when it was detected that the component/
sub-component was added to the chassis. If this has not occurred since 
the cold/warm start of the agent, then the value is zero. 

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов