Nortel 425-24T Скачать руководство пользователя страница 416

Страница: 416 / 488

416

Installing an SFP Transceiver

320985-A Rev 01

Figure 170

Removing an SFP

Slide the SFP out of the module SFP slot.

If the SFP does not slide easily from the module slot, use a gentle side-to-side
rocking motion while firmly pulling the SFP from the slot.

Attach a dust cover over the fiber optic bores and store the SFP in a safe place
until needed.

Technical Specifications

This section includes the following topics:

•

“SFP specifications” on page 417

•

“CWDM SFP specifications” on page 421

Note:

If you are discarding the SFP, be sure to dispose the SFP

according to national laws and regulations.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 416 / 488

Результаты поиска

Содержание 425-24T

Отзывы: