Nortel 425-24T Скачать руководство пользователя страница 145

Страница: 145 / 488

Chapter 3 CLI Basics

145

System Configuration Guide

Figure 36

displays sample output from the

show mac-address-table

command.

Figure 36

show mac-address-table command output

mac-address-table aging-time command

The

mac-address-table aging-time

command sets the time that the switch

retains unseen MAC addresses. The syntax for the

mac-address-table

aging-time

command is:

mac-address-table aging-time <time>

The

mac-address-table aging-time

command is in the config command

mode.

Table 27

describes the parameters and variables for the

mac-address-table

aging-time

command.

Table 27

mac-address-table aging-time command parameters and variables

Parameters
and
variables

Description

time

Enter the aging time in seconds that you want for MAC
addresses before they are flushed.

425-48T(config)#show mac-address-table

Mac Address Table Aging Time: 400

Number of addresses: 13

MAC Address Source MAC Address Source

----------------- -------- ----------------- --------

00-00-81-9B-12-78 Trunk: 3 00-00-E2-13-38-38 Trunk: 3

00-00-E2-1F-9D-0D Trunk: 3 00-04-DC-6F-43-F4 Trunk: 3

00-09-97-89-82-C1 Trunk: 3 00-0C-F8-1A-0F-F8 Trunk: 3

00-0C-F8-61-00-01 Trunk: 3 00-0F-3D-E5-28-01 Trunk: 3

00-0F-6A-82-2E-C1 Trunk: 3 00-0F-6A-82-36-21 Trunk: 3

00-0F-CD-BF-1E-80 00-80-2D-6E-47-38 Trunk: 3

00-80-2D-6E-47-82 Trunk: 3 08-00-20-9F-F3-2C Trunk: 3

425-48T(config)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 145 / 488

Результаты поиска

Содержание 425-24T

Отзывы: