Nortel 425-24T Скачать руководство пользователя страница 138

Страница: 138 / 488

138

Chapter 3 CLI Basics

320985-A Rev 01

show sys-info command

The

show sys-info

command displays the current system characteristics. The

syntax for the

show sys-info

command is:

show sys-info

The

show sys-info

command is in the privExec command mode.

The

show sys-info

command has no parameters or variables.

Figure 30

displays sample output from the

show sys-info

command.

Figure 30

show sys-info command output

To change the system contact, name, or location, refer to the

snmp-server

command (see

Configuring and Managing Security for Nortel Ethernet Switches

325 and 425, Software Release 3.6

(320988-A)).

425-48T#show sys-info

Operation Mode: Switch

MAC Address: 00-0F-CD-BF-1E-80

Reset Count: 34

Last Reset Type: Power Cycle

Power Status: Primary Power

Autotopology: Enabled

Local GBIC Type: (port 49) GBIC is missing

Local GBIC Type: (port 50) GBIC is missing

sysDescr: Ethernet Switch 425-48T

HW:00 FW:3.5.0.2 SW:v3.6.0

Mfg Date: 05122004

Serial #: SACC2600E5

Operational State:Normal

sysObjectID: 1.3.6.1.4.1.45.3.57.1

sysUpTime: 2 days, 17:26:24

sysNtpTime: SNTP not synchronized.

sysServices: 3

sysContact: c

sysName: Ethernet 425-48T

sysLocation:

425-48T#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 138 / 488

Результаты поиска

Содержание 425-24T

Отзывы: