Nortel 425-24T Скачать руководство пользователя страница 382

Страница: 382 / 488

382

Chapter 11 Administering the switch using Web-based management

320985-A Rev 01

Click

To change the Ethernet Switch 425 in its stacking mode to system defaults:

From the main menu, choose

Administration > Reset to Default

The

Reset to Default page

opens

(Figure 156)

Figure 156

Reset to Default page

Click

Submit

Logging out of the management interface

To log out of the Web-based management user interface:

From the main menu, choose

Administration > Logout

A logout message displays.

Figure 157

Logout message

Do one of the following:

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 382 / 488

Результаты поиска

Содержание 425-24T

Отзывы: