manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 363 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 363

Chapter 9 Configuring the switch using Device Manager

363

System Configuration Guide

 

Figure 146   

SNTP dialog box

Table 137

 describes the 

SNTP

 dialog box fields.

Table 137   

SNTP dialog box fields

Field

Description

PrimaryServer 
Address

The IP address of the primary SNTP server.

SecondaryServer 
Address

The IP address of the secondary SNTP server.

State

Controls whether the device uses the Simple Network Time Protocol 
(SNTP), to synchronize the device's clock to the Coordinated 
Universal Time (UTC). If the value is disabled, the device will not 
synchronize it's clock using SNTP.

If the value is unicast, the device will synchronize shortly after boot 
time when network access becomes available, and periodically 
thereafter. 

SyncInterval

Controls the frequency, in hours, that the device will attempt to 
synchronize with the NTP servers

ManualSync 
Request

Specifies that the device to immediately attempt to synchronize with 
the NTP servers. 

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов