manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 78 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 78

78

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

Back panel 

Figure 9

 shows the back panel of the Ethernet Switch 425.

Figure 9   

Ethernet Switch 425 back panel

Table 10

 describes the components on the back panel.

Cascade Up and Down connectors

The Cascade Up and Down connectors allow the Ethernet Switch 425 to be 
connected to the upstream unit’s Cascade Up connector, or to the downstream 
unit’s Cascade Down connector (see 

“Stack configurations” on page 90

.)

Cooling fans

Two cooling fans are located on the side of the Ethernet Switch 425 to provide 
cooling for internal components. (See 

Figure 6 on page 67

.) When you install the 

switch, ensure that there is adequate space on both sides of the switch for 
ventilation. For more information on installing the Ethernet Switch 425, see 

Installing the Ethernet Switch 425 

 (217150-B).

Table 10   

Components on the Ethernet Switch 425

 

back panel

Item

Description

1

AC power receptacle

2

Cascade Up and Down Connectors

100-240 V-
50-60Hz 2A

Cascade

Down

Up

11110EA

1

2

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов