Nortel 425-24T Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 488

Nortel 425-24T Скачать руководство пользователя страница 45

Chapter 1 About Ethernet Switches 325 and 425

45

System Configuration Guide

If you set a password using the

cli password

command, the

Console/Comm

Port Configuration

screen, or the

Password Setting

Web-based management

page, the next time you log in to the switch, you are prompted to enter a valid
username. Therefore, ensure you are aware of the valid usernames (default

RW

and

RO

) before you change passwords.

For more information, refer to

Configuring and Managing Security for Nortel

Ethernet Switches 325 and 425, Software Release 3.6

(320988-A).

Radius password fallback enhancement

With Release 3.6 software, you can configure RADIUS password fallback as an
option when you use RADIUS authentication for login and password.

When RADIUS password fallback is enabled and the RADIUS server is
unavailable or unreachable, you can use the local switch or stack password to log
in to the switch or stack.

When RADIUS password fallback is disabled, you must specify the RADIUS
username and password from the NetLogin screen. You cannot log in to the
switch or stack unless the RADIUS server is configured and reachable in order to
authenticate the login and password.

The Radius password fallback feature is disabled by default.

You can use the Console Interface or the

radius-server password

fallback

CLI command to enable this feature.

For more information, refer to

Configuring and Managing Security for Nortel

Ethernet Switches 325 and 425, Software Release 3.6

(320988-A).

«
...
43
44
45
46
47
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов