manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 364 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 364

364

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Displaying topology information using Device Manager

This chapter describes diagnostic information available in Device Manager on the 
following tabs:

•

“Topology tab”

•

“Topology Table tab” on page 365

Topology tab

To view topology information:

➨

From the Device Manager menu bar, select 

Edit > Diagnostics

.

The 

Diagnostics

 dialog box opens with the 

Topology

 tab displayed 

(Figure 147)

.

LastSyncTime

Specifies the Coordinated Universal Time (UTC) when the device 
last synchronized with an NTP server.

LastSyncSource

Specifies the IP source address of the NTP server with which this 
device last synchronized

NextSyncTime

Specifies the the Coordinated Universal Time (UTC) at which the 
next synchronization is scheduled.

PrimaryServer 
SynchFailures

Specifies the number of times the switch failed to synchronize with 
the primary server address. However, synchronization with the 
secondary server address may still occur.

SecondaryServer 
SynchFailures

Specifies the number of times the switch failed to synchronize with 
the secondary server address, 

CurrentTime

Specifies the switch's current Coordinated Universal Time (UTC).

Note: 

In order to clear out the PrimaryServerAddress and 

SecondaryServerAddress, you must first set the State to disabled.

Table 137   

SNTP dialog box fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов