manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 88 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 88

88

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

The Ethernet Switch 425 does not support stack redundancy. In case of cable or 
unit failure, all units of the stack begin to work as standalone switches. However, 
the stack is automatically formed again once the missing cable is re-inserted or the 
faulty unit is replaced.

Ethernet units in a stack are interconnected through FireWire cables. Ensure that 
the downlink connection on a unit is always connected to the Up link of the next 
unit in the ring.

Base unit

The base unit is the unique unit in the stack that you can configure with the User 
Interface button on the front panel. A single Ethernet Switch 425-24T or Ethernet 
Switch 425-48T in the stack 

must

 be configured as the base unit. You can assign 

any unit in the stack as the base unit.

The physical order of all other units in the stack is determined by the position of 
the base unit within the stack. This is important for network management 
applications that view the physical ordering of the units within the stack.

Some characteristics of the base unit are described in the following sections.

Initial installation

During the initial installation

 

of the stack, the software automatically determines 

the physical order of all units in the stack according to the position of the base unit 
within the stack. Thereafter, the individual units maintain their original unit 
numbering, even if you change the position of one or more units in the stack.

Note: 

Only Ethernet Switch 425-24T and Ethernet Switch 425-48T can 

operate together in the stack mode in release 3.6 software.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов