Nortel 425-24T Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 488

Nortel 425-24T Скачать руководство пользователя страница 137

Chapter 3 CLI Basics

137

System Configuration Guide

Warning the switch/stack has been set to reload in <xx>

minutes. Current configuration has NOT been saved.

Configuration must be explicitly saved.

Once the reload timer expires, the switch resets, reloads the last

saved

configuration, and re-enables the autosave feature.

The syntax for the

reload

command is:

reload [force] [minutes-to-wait <1-60>] [cancel]

describes the parameters and variables for the

interface

command.

The

reload

command is in the privExec command mode.

Managing basic system information

This section shows you how to view basic system information, such as the current
software version and the stack mode; you can renumber the units within a stack.
The following topics are covered:

•

“show sys-info command”

•

“show tech command” on page 139

•

“show stack-info command” on page 141

•

“show stacking-mode command” on page 142

•

“renumber unit command” on page 143

Table 25

reload command parameters and variables

Parameters
and variables

Description

force

Instructs the switch to skip the reload confirmation prompt.

minutes-to-wait
<1-60>]

Specifies the number of minutes that pass before the switch reloads
itself. The default wait time is set at 10 minutes.

cancel

Aborts all scheduled switch reloads

«
...
135
136
137
138
139
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов