Nortel 425-24T Скачать руководство пользователя страница 139

Страница: 139 / 488

Chapter 3 CLI Basics

139

System Configuration Guide

show tech command

The

show tech

command displays the system information. The syntax for the

show tech

command is:

show tech

The

show tech

command is in the privExec command mode. The

show tech

command has no parameters or variables.

Figure 31

Figure 31 on page 139

, and

Figure 32 on page 140

display a sample

output from the

show tech

command.

Figure 31

show tech command output

425# show tech

*****SYS Info*****

System Information:

Operation Mode: Switch

MAC Address: 00-09-97-A2-9D-80

Reset Count: 123

Last Reset Type: Management Reset

Autotopology: Enabled

sysObjectID: 1.3.6.1.4.1.45.3.57.2

sysUpTime: 2 days, 04:41:28

sysNtpTime: SNTP not synchronized.

sysServices: 3

sysContact:

sysName: 425

sysLocation:

Unit #1:

Switch Model: 425-24T

MDA Model: None

Cascade Module: 400-ST1

Hardware Version: 0B

Firmware Version: 3.5.0.2

Software Version: v3.6.0

Serial Number: SACC25003U

Manufacturing Date: 05232003

Power Status: Primary

Fan #1 Status: Normal

Fan #2 Status: Normal

*****UI Button*****

Unit # Button Mode

------ -------------

1 Enabled

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 139 / 488

Результаты поиска

Содержание 425-24T

Отзывы: