Nortel 425-24T Скачать руководство пользователя страница 298

Страница: 298 / 488

298

Chapter 7 System configuration using the CLI

320985-A Rev 01

no autotopology command

The

autotopology

command disables the Autotopology protocol. The

syntax for the

autotopology

command is:

no autotopology

The

autotopology

command is in the config command mode.

The

autotopology

command has no parameters or values.

default autotopology command

The

default

autotopology

command enables the Autotopology protocol. The

syntax for the

default

autotopology

command is:

default autotopology

The

default

autotopology

command is in the config command mode.

The

default

autotopology

command has no parameters or values.

show autotopology settings

The

show autotopology settings

command displays information on the

Autotopology configuration. The syntax for the

show autotopology settings

command is:

show autotopology settings

The

show autotopology settings

command is in the privExec mode.

The

show autotopology settings

command has no parameters or variables.

Figure 111

displays a sample output of the

show autotopology settings

command.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 298 / 488

Результаты поиска

Содержание 425-24T

Отзывы: