manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 426 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 426

426

Connectors and pin assignments

320985-A Rev 01

 

Table 164

 lists the RJ-45 (8-pin modular) port connector pin assignments.

MDI and MDI-X devices

Media dependent interface (MDI) is the IEEE standard for the interface to 
unshielded twisted pair (UTP) cable.

For two devices to communicate, the transmitter of one device must connect to the 
receiver of the other device. The connection is established through a crossover 
function, which can be a crossover cable or a port that implements the crossover 
function internally.

Ports that implement the crossover function internally are known as MDI-X ports, 
where X refers to the crossover function.

The following sections describe the use of straight-through and crossover cables 
for connecting MDI and MDI-X devices.

Table 164   

RJ-45 port connector pin assignments

Pin

Signal

Description

1

RX+

Receive Data +

2

RX-

Receive Data -

3

TX+

Transmit Data +

4

Not applicable

Not applicable

5

Not applicable

Not applicable

6

TX-

Transmit Data -

7

Not applicable

Not applicable

8

Not applicable

Not applicable

Note: 

For the transmitter of one device to connect to the receiver of 

another device, the total number of crossovers must always be an odd 
number.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов