manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 106 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 106

106

Chapter 2 Using the console interface

320985-A Rev 01

 

Port list syntax

When you enter a port list in a stack configuration, you must specify either a unit/
port list, 

NONE

, or 

ALL

. In a stack configuration, 

ALL

 indicates all of the stack 

port; whereas, in a standalone scenario, 

ALL

 indicates all ports of the switch.

A unit/port number list is composed of one or more list items, each of which can 
be a single number or a range of numbers (where the numbers represents one or 
more ports). If a list item is preceded by a number and then a slash (/), the number 
represents a stack unit.

For example, 1/1-7,2/1-7,2/9,3/1-4,4/12 is a valid unit/port number list (see entry 
S1 in 

Figure 21 on page 107

). It represents the following port order:

•

Unit 1: ports 1 to 7

•

Unit 2: ports 1 to 7 and port 9

•

Unit 3: ports 1 to 4

•

Unit 4: port 12

Note: 

NONE

 and 

ALL

 must be entered in uppercase characters as 

shown in the screen prompt.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов