Nortel 425-24T Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 488

Nortel 425-24T Скачать руководство пользователя страница 143

Chapter 3 CLI Basics

143

System Configuration Guide

displays sample output from the

show stacking-mode

command.

Figure 35

show stacking-mode command output

renumber unit command

This command is applicable only to Ethernet Switch 425-24T, in its stacked
mode.

The

renumber unit

command changes the unit number of each switch in the

stack. The syntax for the

renumber unit

command is:

renumber unit

The

renumber unit

command is in the config command mode.

The

renumber unit

command has no parameters or variables.

Managing MAC address forwarding database table

This section describes the commands to view the contents of the MAC address
forwarding database table, as well as setting the age-out time for the addresses.
The following topics are covered:

•

“show mac-address-table command” on page 144

•

“mac-address-table aging-time command” on page 145

•

“default mac-address-table aging-time command” on page 146

Note:

This command does not take effect until you reset the stack.

425-24T>show stacking-mode

Current mode for unit 1 is stackable, base unit set.

Next mode for unit 1 is stackable, base unit set.

Current mode for unit 2 is stackable, base unit not set.

Next mode for unit 3 is stackable, base unit not set.

Next mode will be applied after reset

«
...
141
142
143
144
145
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов