manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 217 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 217

Chapter 6 System configuration using the Console Interface

217

System Configuration Guide

 

•

BootP or Last Address

BootP When Needed

Allows the switch to request an IP address if one has not already been set from the 
console terminal. The Ethernet Switch 325/425 operates in the BootP When 
Needed mode as described in the steps below:

•

When the IP data is entered from the console terminal, the data becomes the 
in-use address of the switch and BootP requests are not broadcast. The switch 
can be managed using this in-band IP address.

•

When the in-band IP address is not set from the console terminal, the switch 
broadcasts BootP requests until it receives a BootP reply containing an IP 
address. If the switch does not receive a BootP reply that contains an IP 
address, the switch cannot be managed in-band.

If an IP address is not currently in use, these actions take effect immediately. If an 
IP address is currently in use, these actions take effect only after the switch is reset 
or power cycled.

BootP Always

This option allows you to manage the switch that has been configured with the IP 
address obtained from the BootP server. The Ethernet Switch 325/425 operates in 
the BootP Always mode as described in the steps below:

•

The switch continues to broadcast BootP requests, regardless of whether an 
in-band IP address is set from the console terminal.

•

If the switch receives a BootP reply that contains an in-band IP address, the 
switch uses this new in-band IP address.

Note: 

Whenever the switch is broadcasting BootP requests, the BootP 

process eventually times out if a reply is not received. When the process 
times out, the BootP request mode automatically changes to BootP 
Disabled mode. To restart the BootP process, change the BootP request 
mode to any of the three following modes: 

•

BootP When Needed 

•

BootP  Always

•

BootP or Last Address

.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов