Nortel 425-24T Скачать руководство пользователя страница 277

Страница: 277 / 488

Chapter 7 System configuration using the CLI

277

System Configuration Guide

show tftp-server command

The

show tftp-server

command displays the IP address of the server used for

all TFTP-related transfers. The syntax for the

show tftp-server

command is:

show tftp-server

The

show tftp-server

command is in the privExec command mode.

The

show tftp-server

command has no parameters or variables.

Figure 102

shows a sample output of the

show tftp-server

command.

Figure 102

show tftp-server command output

tftp-server command

The

tftp-server

command assigns the address for the stack or switch to use for

TFTP services. The syntax of the

tftp-server

command is:

tftp-server <XXX.XXX.XXX.XXX>

The

tftp-server

command is in the config command mode.

Table 77

describes the parameters and variables for the

tftp-server

command.

Table 77

tftp-server command parameters and variables

Parameters and
variables

Description

XXX.XXX.XXX.XXX

Enter the dotted-decimal IP address of the server you want to
use for TFTP services.

425-48T(config-if)#show tftp-server

TFTP Server IP address : 198.202.188.174

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 277 / 488

Результаты поиска

Содержание 425-24T

Отзывы: