Nortel 425-24T Скачать руководство пользователя страница 285

Страница: 285 / 488

Chapter 7 System configuration using the CLI

285

System Configuration Guide

Table 83

describes the parameters and variables for the

show interfaces

config

command.

Figure 104

displays a sample output of the

show interfaces config

command.

Figure 106

show interfaces config command output

Saving the configuration to NVRAM

You can save your configuration parameters to Non-Volatile RAM (NVRAM)
using any of the following CLI commands:

•

“copy config nvram command” on page 285

•

“write memory command” on page 286

•

“save config command” on page 286

copy config nvram command

The

copy config nvram

command copies the current configuration to

NVRAM. The syntax for the

copy config nvram

command is:

Table 84

show interfaces config command parameters and variables

Parameters and
variables

Description

Enter the ports you want to display.

425 (config)#show interfaces 1/1,1/2 config

Status Auto Flow

Port Trunk Admin Oper Link LinkTrap Negotiation Speed Duplex Control

--------- ----- ------ --- --- ------- ---------- ----- ------ ------

1 Enable Down Down Enabled Enabled

*****Spanning-tree port configurations*****

Port Role State STP Status Oper Status

---- ---------- ---------- ---------- -----------

1 Root Forwarding Enabled Enabled

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 285 / 488

Результаты поиска

Содержание 425-24T

Отзывы: