manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 290 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 290

290

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Figure 108   

show sntp command output

sntp enable command

The 

sntp enable 

command enables SNTP. The syntax for the 

sntp enable 

command is:

sntp enable

The 

sntp enable 

command is in the config command mode. 

The 

sntp enable 

command has no parameters or variables. 

no sntp enable command

The 

no

 

sntp enable 

command disables SNTP. The syntax for the 

no sntp 

enable 

command is:

no sntp enable

The 

no sntp enable 

command is in the config command mode.

The 

no sntp enable 

command has no parameters or variables. 

Note: 

The default setting for SNTP is disabled.

425-48T(config-if)#show sntp

SNTP Status:                    Disabled

Primary server address:         0.0.0.0

Secondary server address:       0.0.0.0

Sync interval:                  24 hours

Last sync source:               0.0.0.0

Primary server sync failures:   0

Secondary server sync failures: 0

Last sync time:                 Not Set

Next sync time:                 Not Set

Current time:                   Not Set

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов