manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 43 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 43

Chapter 1 About Ethernet Switches 325 and 425

43

System Configuration Guide

 

In addition to the four mandatory TLVs, Release 3.6 software supports the basic 
management TLV set. You can specify which of these optional TLVs to include 
in the transmitted LLDPDUs for each port. 

The optional management TLVs are as follows:

•

Port Description TLV

•

System  Name  TLV

•

System Description TLV

•

System Capabilities TLV (indicates both the system supported capabilities 
and enabled capabilities, such as end station, bridge, or router)

•

Management Address TLV

Transmitting LLDPDUs

When a transmit cycle is initiated, the LLDP manager extracts the managed 
objects from the LLDP local system MIB and formats this information into TLVs. 
The TLVs are then inserted into the LLDPDU.

LLDPDU are regularly transmitted at a user-configurable transmit interval 
(tx-delay), or when any of the variables contained in the LLPDU is modified on 
the local system (such as system name or management address). Tx-delay is the 
minimum delay between successive LLDP frame transmissions.

TLV system MIBs

The LLDP local system MIB stores the information for constructing the various 
TLVs to be sent. The LLDP remote systems MIB stores the information received 
from remote LLDP agents.

LLDPDU and TLV error handling

LLDPDUs and TLVs that contain detectable errors are discarded. TLVs that are 
not recognized, but that also contain no basic format errors, are assumed to be 
validated and are stored for possible later retrieval by network management.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов