Nortel 425-24T Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 488

Nortel 425-24T Скачать руководство пользователя страница 53

Chapter 1 About Ethernet Switches 325 and 425

53

System Configuration Guide

VLAN Configuration Control is only applied to ports with the tagging modes of
Untag All and Tag PVID Only. Ports with the tagging modes of Tag All and
Untag PVID Only are not governed by VLAN Configuration Control. Ports with
the tagging modes of Tag All and Untag PVID Only can belong to multiple
VLANs regardless of VLAN Configuration Control settings and must have their
PVID manually changed.

For more information, refer to

Configuring VLANs, Spanning Tree, and

MultiLink Trunking for Nortel Ethernet Switches 325 and 425, Software
Release 3.6

(320986-A).

Port mirroring configuration rules

Additional port mirroring configuration rules are available in

System Monitoring

Guide for Nortel Ethernet Switches 325 and 425, Software
Release 3.6

(320989-A).

Other features

SFP GBIC Support on the Ethernet Switch 425

Small Form Factor Pluggable transceivers (SFPs) are hot-swappable input/output
enhancement components designed for use with Nortel products to allow Gigabit
Ethernet ports to link with other Gigabit Ethernet ports over various media types.

The Ethernet Switch 425 supports the following SFPs:

•

1000Base-SX SFP GBIC (mini-GBIC, connector type: LC)

•

1000Base-SX SFP GBIC (mini-GBIC, connector type: MT-RJ)

•

1000Base-LX SFP GBIC (mini-GBIC, connector type: LC)

•

CWDM SFPs

For more information about the SFP GBICs see

Appendix A, “Installing an SFP

Transceiver,” on page 409

«
...
51
52
53
54
55
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов