Nortel 425-24T Скачать руководство пользователя страница 131

Страница: 131 / 488

Chapter 3 CLI Basics

131

System Configuration Guide

Figure 29

help command output in privExec mode

no command

The

command is always used as a prefix to a configuration command, and it

negates the action performed by that command. The effect of the

command is

to remove or to clear the configuration controlled by the specified command.
Various

commands are in the config and config-if command modes.

Refer to

Appendix E, “Command List,” on page 447

for an alphabetical listing of

all

commands.

default command

The

default

command is always used as a prefix to a configuration command,

and it restores the configuration parameters to default values. The default values
are specified by each command.

Refer to Appendix A for an alphabetical listing of all

default

commands.

Note:

Not all configuration commands support the

prefix

command.

Note:

Not all commands support the

default

prefix

command.

425-48T>help

Context help may be requested at any point in a command by entering

a question mark '?'. If nothing matches, the help list will be empty

and you must backup until entering a '?' shows the available options.

Two styles of help are provided:

1. Full help is available when you are ready to enter a

command argument (e.g. 'show?') and describes each possible

argument.

2. Partial help is provided when an abbreviated argument is entered

and you want to know what arguments match the input

(e.g. 'show pr?'.)

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 131 / 488

Результаты поиска

Содержание 425-24T

Отзывы: