manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 249 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 249

Chapter 6 System configuration using the Console Interface

249

System Configuration Guide

 

Setting local time zone

SNTP uses Universal Coordinated Time (UTC) for all time synchronizations so it 
is not affected by different time zones. In order for the switch report the correct 
time for your local time zone and daylight savings time, you must use the 
following commands:

•

“clock time-zone” on page 294

•

“no clock time-zone” on page 295

•

“clock summer-time” on page 295

•

“no clock summer-time” on page 296

•

“show clock time-zone” on page 296

•

“show clock summer-time” on page 296

Using DNS to ping and Telnet

Using the DNS client, you can ping or Telnet to a host server or to a host by name. 

To use this feature, you must configure at least one Domain Name Server (DNS); 
You may also configure a default domain name. If you configure a default domain 
name, that name is appended to host names that do not contain a dot. The default 
domain name and addresses are saved in NVRAM.

The host names for ping and Telnet cannot be longer than 63 alphanumeric 
characters, and the default DNS domain name cannot be longer than 255 
characters.

Configuring with CLI

Use the CLI to configure the DNS client. Following are the commands used to 
configure the DNS client using the CLI.

•

show ip dns command

•

ping  command

•

ip name-server command

•

no ip name-server command

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов