Nortel 425-24T Скачать руководство пользователя страница 284

Страница: 284 / 488

284

Chapter 7 System configuration using the CLI

320985-A Rev 01

Figure 105

show interfaces command output

show interfaces config command

The

show interfaces config

command displays the current operational

status of interfaces and provides supplementary information about the current port
settings for Spanning Tree Protocol.

The syntax for the

show interfaces config

command is:

show interfaces [<portlist>] config

The

show interfaces config

command is in the privExec command mode.

425-48T(config-if)#show interfaces

Status Auto Flow

Port Trunk Admin Oper Link LinkTrap Negotiation Speed Duplex Control

---- ----- ------- ---- ---- -------- ----------- -------- ------ -------

1 Enable Down Down Enabled Enabled

2 Enable Down Down Enabled Enabled

3 Enable Down Down Enabled Enabled

4 Enable Down Down Enabled Enabled

5 Enable Down Down Enabled Custom

6 Enable Down Down Enabled Enabled

7 Enable Down Down Enabled Enabled

8 Enable Down Down Enabled Enabled

9 Enable Down Down Enabled Enabled

10 Enable Down Down Enabled Enabled

11 Enable Down Down Enabled Enabled

12 Enable Down Down Enabled Enabled

13 Enable Down Down Enabled Enabled

14 Enable Down Down Enabled Enabled

15 Enable Down Down Enabled Enabled

16 Enable Down Down Enabled Enabled

17 Enable Down Down Enabled Enabled

18 Enable Down Down Enabled Enabled

19 Enable Down Down Enabled Enabled

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 284 / 488

Результаты поиска

Содержание 425-24T

Отзывы: