manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 294 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 294

294

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Setting local time zone

SNTP uses Universal Coordinated Time (UTC) for all time synchronizations so it 
is not affected by different time zones. In order for the switch report the correct 
time for your local time zone and daylight savings time, you must use the 
following commands:

•

“clock time-zone” on page 294

•

“no clock time-zone” on page 295

•

“clock summer-time” on page 295

•

“no clock summer-time” on page 296

•

“show clock time-zone” on page 296

•

“show clock summer-time” on page 296

clock time-zone 

The 

clock time-zone

 command sets the local time zone relative to Universal 

Coordinated Time (UTC). The syntax for the 

clock time-zone

 command is:

clock time-zone <zone> <

hours

> <

minutes

>

The 

clock time-zone 

command is in the config command mode. 

Table 89

 describes the parameters and variables for the 

clock time-zone 

command.

Table 89   

clock time-zone command parameters and variables

Parameters and 
variables

Description

zone 

Time zone acronym that can be displayed when showing system 
time (Range: Up to 4 characters)

hours

Hours difference from UTC. (Valid Range: –12 to +12)

minutes

Optional minutes difference from UTC. (Range: 0–59)

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов