manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 373 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 373

Chapter 10 Configuring ports using Device Manager

373

System Configuration Guide

 

Mtu

Size of the largest packet, in octets, that can be sent or received on the 
interface.

PhysAddress

MAC address assigned to a particular interface.

AdminStatus

Current administrative state of the device, which can be one of the 
following:

•

up

•

down

When a managed system is initialized, all interfaces start with 
AdminStatus in the up state. AdminStatus changes to the down state 
(or remains in the up state) as a result of either management action or 
the configuration information available to the managed system.

OperStatus

Current operational state of the interface, which can be one of the 
following:

•

up

•

down

•

testing 

If AdminStatus is up, then OperStatus should be up if the interface is 
ready to transmit and receive network traffic. If AdminStatus is down, 
then OperStatus should be down. It should remain in the down state if 
and only if there is a fault that prevents it from going to the up state. The 
testing state indicates that no operational packets can be passed. 

LastChange

Value of the time the interface entered its current operational state. If 
the current state was entered prior to the last reinitialization of the local 
network management subsystem, the value is zero.

LinkTrap

Specifies whether linkUp/linkDown traps should be generated for this 
interface

Speed

The estimate bandwidth of the interface in bits per second (bps). For 
interfaces that do not vary in bandwidth or have no way to estimate the 
bandwidth, this object should contain the nominal bandwidth. If the 
bandwidth of the interface is greater than the maximum value reported 
by the object, then the object displays its maximum value 
(4,294,967,295). For a sub-layer that has no concept of bandwidth, the 
object should be zero.

AutoNegotiate

Indicates whether the port is enabled (checked) for autonegotiation or 
not.

AdminDuplex

The current administrative duplex mode of the port (half or full).

OperDuplex

Indicate current duplex value of the port.

AdminSpeed

Set the speed of a port: none, mbps10, and mbps100

OperSpeed

The current operating speed of the port.

Table 141   

Interface tab fields for multiple ports (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов