manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 370 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 370

370

Chapter 10 Configuring ports using Device Manager

320985-A Rev 01

 

Table 140

 describes the 

Interface

 tab fields for a single port.

Table 140   

Interface tab fields for a single port

Field

Description

Index

A unique value assigned to each interface. The value ranges between 1 
and 512. 

Name

Specifies a name for the port.

Descr

The type of switch and number of ports.

Type

The media type of this interface.

Mtu

The size of the largest packet, in octets, that can be sent or received on 
the interface.

PhysAddress

The MAC address assigned to a particular interface.

AdminStatus

The current administrative state of the device, which can be one of the 
following:

•

up

•

down

When a managed system is initialized, all interfaces start with 
AdminStatus in the up state. AdminStatus changes to the down state (or 
remains in the up state) as a result of either management action or the 
configuration information available to the managed system.

OperStatus

The current operational state of the interface, which can be one of the 
following:

•

up

•

down

•

testing 

If AdminStatus is up, then OperStatus should be up if the interface is 
ready to transmit and receive network traffic. If AdminStatus is down, then 
OperStatus should be down. It should remain in the down state if and only 
if there is a fault that prevents it from going to the up state. The testing 
state indicates that no operational packets can be passed. 

LastChange

The value of sysUpTime at the time the interface entered its current 
operational state. If the current state was entered prior to the last 
reinitialization of the local network management subsystem, the value is 
zero.

LinkTrap

Specifies whether linkUp/linkDown traps should be generated for this 
interface

Speed

Current speed.

AutoNegotiate

Indicates whether this port is enabled for autonegotiation or not.

AdminDuplex

The current administrative duplex mode of the port (half or full).

OperDuplex

The current mode of the port (half duplex or full duplex).

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов