manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 388 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 388

388

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

2

Type information in the text boxes, or select from a list.

BootP or Last Address

Choose this mode to inform the 
switch at each startup, to obtain its IP 
configuration using BootP. If the 
BootP request fails, the switch uses 
the network parameters stored in its 
non-volatile memory.

Note:

 Valid parameters obtained in 

using BootP always replace current 
information stored in the non-volatile 
memory.

Note:

 Whenever the switch is 

broadcasting BootP requests, the 
BootP process times out if a reply is 
not received within 7 minutes 
(approximately). When the process 
times out, the BootP request mode 
automatically changes to BootP 
Disabled mode. To restart the BootP 
process, change the BootP request 
mode to any of the three following 
modes: BootP When Needed, BootP 
Always, or to BootP or Last Address. 

IP Setting

In-Band 
Stack IP 
Address

XXX.XXX.XXX.XXX

Type a new stack IP address in the 
appropriate format.

In-Band 
Switch IP 
Address

XXX.XXX.XXX.XXX

Type a new switch IP address in the 
appropriate format.

Note:

 When the IP address is 

entered in the In-Band IP Address 
field, and the In-Band Subnet Mask 
field value is not present, the 
software provides an 

in-use

 default 

value for the In-Band Subnet Mask 
field that is based on the class of the 
IP address entered in the In-Band IP 
Address field.

In-Band 
Subnet Mast

XXX.XXX.XXX.XXX

Type a new subnet mask in the 
appropriate format.

Gateway 
Setting

Default 
Gateway

XXX.XXX.XXX.XXX

Type an IP address for the default 
gateway in the appropriate format.

Table 144   

IP page items (continued) 

Section

Item

Range

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов