manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 199 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 199

199

System Configuration Guide

 

Chapter 5
Using the Web-based management interface

This chapter describes the requirements for using the Web-based management 
interface and how to use it as a tool to configure your Ethernet Switch 325/425.

Requirements

To use the Web-based management interface, you need the following items:

•

A computer connected to a network port that is a member of the management 
VLAN

•

One of the following Web browsers installed on the computer:

— Microsoft

*

 Internet Explorer, version 4.0 or later on Windows 95, 

Windows 98, Windows 2000, Windows NT

*

, or Windows XP

*

— Netscape Navigator

*

, version 4.51 or later on Windows 95, Windows 98, 

Windows 2000, Windows NT, Windows XP, and UNIX

*

•

IP address of the Ethernet Switch 325/425

For instructions to set the IP address of the switch, refer to 

“IP Configuration/

Setup screen” on page 214

.

Note: 

The Web pages of the Web-based management interface may load 

at different speeds depending on the Web browser you use.

Note: 

In order to use the Ethernet Switch 325/425 Web-based 

management functionality, such as downloading software, you must 
connect your TFTP server to an Ethernet Switch 325/425.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов