Nortel 425-24T Скачать руководство пользователя страница 170

Страница: 170 / 488

170

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

When the installation is complete, the

Install Complete

dialog box opens

(

Figure 53

Figure 53

Install Complete dialog box

Click

Done

to exit the installation.

JDM is now installed on your machine.

Removing JDM in Unix or Linux environments

In a UNIX or Linux environment, complete the following steps to remove the
existing JDM software:

Navigate to the directory where the JDM software is installed (for example

/JDM

Open the UninstallerData sub-directory.

Run the following file:

Uninstall_Java_Device_Manager

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 170 / 488

Результаты поиска

Содержание 425-24T

Отзывы: