manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 252 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 252

252

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Configuring the switch IP address, subnet mask and 
default gateway

IP notation

To enter IP addresses and subnet masks in the CLI, enter both the IP address and 
the subnet mask in dotted decimal notation (XXX.XXX.XXX.XXX).

Assigning and clearing IP addresses

Using the CLI, you can assign IP addresses and Gateway addresses, clear these 
addresses, and view configured IP addresses. This section covers these topics:

•

“ip address command”

•

“no ip address command” on page 253

•

“ip default-gateway command” on page 254

•

“no ip default-gateway command” on page 254

•

“show ip command” on page 255

ip address command

The 

ip address

 

command sets the IP address and subnet mask for the switch or 

a stack. The syntax for the 

ip address

 command is:

ip address [stack|switch|unit] <XXX.XXX.XXX.XXX> [netmask 

<XXX.XXX.XXX.XXX>]

The 

ip address

 

command is in the config command mode. 

If you do not enter either the stack or switch parameter, the system automatically 
modifies the stack IP address when in stack mode and modifies the switch IP 
address when in standalone mode.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов