manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 314 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 314

314

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

ui-button unit command

The

 ui-button unit 

command enables UI button on selected unit in the range 

of <1-8>.

The syntax for the 

ui-button unit 

command is:

ui-button unit <unit #>

The

 ui-button unit 

command is in the config command mode. 

The

 ui-button unit 

command has no parameters or variables. 

show ui-button

You can check if the UI button is enabled or disabled using the 

show ui button

 

command. The syntax for the

 show ui-button 

command is:

show ui-button

The

 show ui-button 

command is in the privExec command mode.

The

 show ui-button 

command has no parameters or variables.

Figure 122

 displays sample output from the

 show ui-button 

command.

Figure 122   

show ui-button command output

Note: 

This command is specific to stacking mode only.

425-48T#show ui-button

 Unit #  Button Mode

 ------  -------------

 1        Enabled

425-48T#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов