Nortel 425-24T Скачать руководство пользователя страница 328

Страница: 328 / 488

328

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

Table 116

describes the parameters and variables for the

flowcontrol

command.

default flowcontrol command

The

default

flowcontrol

command is used only on Gigabit Ethernet ports

and sets the flow control to auto, which automatically detects the flow control.
The syntax for the

default

flowcontrol

command is:

default flowcontrol [port <portlist>]

The

default

flowcontrol

command is in the config-if mode.

Table 117

describes the parameters and variables for the

default

flowcontrol

command.

Table 116

no flowcontrol command parameters and variables

Parameters and
variables

Description

port <portlist>

Specifies the port numbers to disable flow control.

Note:

If you omit this parameter, the system uses the port

number you specified in the

interface

command.

Table 117

default flowcontrol command parameters and variables

Parameters and
variables

Description

port <portlist>

Specifies the port numbers to default to auto flow control.

Note:

If you omit this parameter, the system uses the port

number you specified in the

interface

command.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 328 / 488

Результаты поиска

Содержание 425-24T

Отзывы: