Nortel 425-24T Скачать руководство пользователя страница 304

Страница: 304 / 488

304

Chapter 7 System configuration using the CLI

320985-A Rev 01

Table 96

describes the parameters and variables for the

lldp tx-tlv

command.

no lldp tx-tlv command

The

no lldp tx-tlv

command specifies the optional TLVs not to include in

the transmitted LLDPDUs. The syntax for the

lldp tx-tlv

command is:

no lldp tx-tlv [port <portlist>] [port-desc] [sys-name]

[sys-desc] [sys-cap] [local-mgmt-addr]

The

no lldp tx-tlv

command is in the config-if command mode.

Table 97

describes the parameters and variables for the

no lldp tx-tlv

command.

Table 96

lldp tx-tlv command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

port-desc

Port description TLV

sys-name

System name TLV

sys-desc

System description TLV

sys-cap System

capabilities

TLV

local-mgmt-addr

Local management address TLV

Table 97

no lldp tx-tlv command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

port-desc

Port description TLV.

sys-name

System name TLV

sys-desc

System description TLV

sys-cap System

capabilities

TLV

local-mgmt-addr

Local management address TLV

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 304 / 488

Результаты поиска

Содержание 425-24T

Отзывы: