Nortel 425-24T Скачать руководство пользователя страница 355

Страница: 355 / 488

Chapter 9 Configuring the switch using Device Manager

355

System Configuration Guide

Figure 140

Telnet window with default banner

To disable the banner:

➨

In the

Banner

tab, click on the

disabled

radio button, and then click

Apply

To check that the banner is disabled:

➨

In the Main Menu, click on

Device > Telnet

The

Telnet

window opens without the banner.

### ### ########### ########## ############# ########### ###

#### ### ############# ############ ############# ########### ###

##### ### ### ### ### ### ### ### ###

###### ### ### ### ### ### ### ### ###

### ### ### ### ### ############ ### ######### ###

### ### ### ### ### ########### ### ######### ###

### ###### ### ### ### ### ### ### ###

### ##### ### ### ### ### ### ### ###

### #### ############# ### ### ### ########### ###########

### ### ########### ### ### ### ########### ###########

Enter Ctrl-Y to begin.

***************************************************************

*** Ethernet Switch 425-24T ***

*** Nortel ***

*** Release 3.6 ***

*** HW:0A FW:3.5.0.2 SW:v3.6.0 ***

***************************************************************

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 355 / 488

Результаты поиска

Содержание 425-24T

Отзывы: