manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 406 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 406

406

Chapter 13 Troubleshooting

320985-A Rev 01

 

Normal power-up sequence

In a normal power-up sequence, the LEDs appear as follows:

1

After power is applied to the switch, the Pwr (Power) LED turns on within 5 
seconds.

2

The switch initiates a self-test, during which the port LEDs display various 
patterns to indicate the progress of the self-test.

3

After the self-test, the remaining port LEDs indicate their operational status, 
as described in 

Table 155

.

Vorsicht: 

Um Verletzungsgefahr durch einen elektrischen Stromschlag 

auszuschließen, nehmen Sie niemals die obere Abdeckung vom Gerät ab. 
Im Geräteinnern befinden sich keine Komponenten, die vom Benutzer 
gewartet werden können.

Avertissement: 

Pour éviter tout risque d'électrocution, ne jamais 

retirer le capot de l'appareil. Cet appareil ne contient aucune pièce 
accessible par l'utilisateur.

Advertencia: 

A fin de evitar daños personales por corrientes eléctricas 

peligrosas, no desmonte nunca la cubierta superior de este dispositivo. 
Los componentes internos no son reparables por el usuario.

Avvertenza: 

Per evitare lesioni fisiche dovute a scariche pericolose di 

corrente, non rimuovere mai il coperchio superiore del dispositivo. I 
componenti interni non possono essere manipolati dall'utente.

 

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов