Nortel 425-24T Скачать руководство пользователя страница 454

Страница: 454 / 488

454

Command List

320985-A Rev 01

no autosave enable

no autotopology

no-banner

no clock summer-time

no clock time-zone

no command

no eapol guest-vlan [enable]

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

no flowcontrol [port <portlist>]

page 298

no ip address {stack|switch}

page 253

no ip address unit <1-8>

page 258

no ip bootp server

page 276

no ip default-gateway

page 254

no ip domain-name

page 265

no ip name-server <A.B.C.D>

page 264

no ipmgr {source-ip [<1-10>]}

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

no ipmgr {telnet|snmp|http}

Configuring and Managing Security for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320988-A)

no lacp aggregation [port <portlist>] enable

Configuring VLANs, Spanning Tree, and
MultiLink Trunking for Nortel Ethernet Switches
325 and 425, Software Release 3.6

(320986-A)

no lacp system-priority

Configuring VLANs, Spanning Tree, and
MultiLink Trunking for Nortel Ethernet Switches
325 and 425, Software Release 3.6

(320986-A)

no lldp port <portlist> config notification

page 302

no lldp port <portlist> status

page 306

no lldp tx-tlv [port <portlist>] [port-desc] [sys-name]
[sys-desc] [sys-cap]

page 304

no logging

System Monitoring Guide for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320989-A)

Table 168

CLI command list (continued)

Command

Page No.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 454 / 488

Результаты поиска

Содержание 425-24T

Отзывы: