Nortel 425-24T Скачать руководство пользователя страница 265

Страница: 265 / 488

Chapter 7 System configuration using the CLI

265

System Configuration Guide

ip domain-name command

The

ip domain-name

command sets the system’s DNS domain name. The

syntax for the

ip domain-name

command is:

ip domain-name [

LINE>]

The

ip domain-name

command is in the config command mode.

Table 70

describes the parameters and variables for the

ip domain-name

command.

The default value for this command is an empty string.

no ip domain-name command

The

ip domain-name

command clears the system’s DNS domain name (sets

it to an empty string). The syntax for the

no ip domain-name

command is:

no ip domain-name

The

no ip domain-name

command is in the config command mode.

The

no ip domain-name

command has no parameters or variables.

default ip domain-name command

The

default

ip domain-name

command clears the system’s DNS domain

name (set it to an empty string). The syntax for the

default ip domain-name

command is:

default ip domain-name

Table 70

ip domain-name command parameters and variables

Parameters and
variables

Description

<LINE>

Enter a DNS domain name.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 265 / 488

Результаты поиска

Содержание 425-24T

Отзывы: