manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 435 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 435

Default settings

435

System Configuration Guide

 

Unit

1

“Port Configuration screen” on 
page 109

. 

Status

Enabled (for all ports)

LnkTrap

On

Autonegotiation

Enabled (for all ports

)

Speed/Duplex

100Mbs/Half (when 
Autonegotiation is Disabled)

Autonegotiation

Enabled

“High Speed Flow Control 
Configuration screen” on page 112

Speed/Duplex

100Mbs/Half (when 
Autonegotiation is Disabled)

Flow Control

Disabled

Trunk

1 to 6 (depending on 
configuration status)

MultiLink Trunk Configuration Menu 
screen (see 

Configuring VLANs, 

Spanning Tree, and 
MultiLink Trunking for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320986-A))

Trunk Members (Unit/Port)

Blank field

STP Learning

Normal

Trunk Mode

Basic

Trunk Status

Disabled

Trunk Name

Trunk #1 to Trunk #6

Traffic Type

Rx and Tx

MultiLink Trunk Utilization screen (see 

Configuring VLANs, 
Spanning Tree, and 
MultiLink Trunking for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320986-A))

Table 167   

Factory default settings (continued)

Field

Default setting

Appears in this CI screen

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов