manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 144 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 144

144

Chapter 3 CLI Basics

320985-A Rev 01

 

show mac-address-table command

The 

show mac-address-table

 command displays the current contents of the 

MAC address forwarding database table. The syntax for the 

show 

mac-address-table

 command is:

show mac-address-table [vid 

<

1-4094>

] [aging-time] 

[address <H.H.H>] [port <LINE>] [include/exclude <

pattern

>]

The 

show mac-address-table

 command is in the privExec command mode.

Table 26

 describes the parameters and variables for the 

show

 

mac-address-table

 

command. 

Table 26   

show mac-address-table command parameters and variables

Parameters and 
variables

Description

vid <1-4094>

Enter the number of the VLAN you want to display the 
forwarding database. 
Default is to display the management VLAN’s database.

aging-time

Displays the time in seconds after which an unused entry is 
removed from the forwarding database.

address <H.H.H>

Displays a specific MAC address if it exists in the database. 
Enter the MAC address you want displayed.

port <LINE>

List of ports.

include/exclude 
<

pattern

>

Allows you to filter the results of the command by printing 
only those entries in the address table that include or exclude 
a given pattern. The value for <

pattern

> must be a sequence 

of 1 to 6 bytes in hex, separated by dashes.

for example: 

show mac-address-table 

port 1/1-5 address include 00-0E-45-23

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов