Nortel 425-24T Скачать руководство пользователя страница 60

Страница: 60 / 488

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

Figure 4

Ethernet Switch 325-24G LED display panel

Table 3

Ethernet Switch 325-24G LED descriptions

Label

Color/Status

Meaning

Link/Activity Green

Station connected at 100 Mbps.

Amber

Station connected at 10 Mbps.

Green/Flashing

Traffic activity at 100 Mbps.

Amber/Flashing

Traffic activity at 10 Mbps.

Off

No link/No traffic.

Half/Full
Duplex

Green

Full duplex

Off

Half duplex connection.

UI Set

Button

The UI Set button is used to reset the switch
without a console connection.

Green/Flashing Indicates

the switch is in cmd mode.

Green

ON for about 3 seconds when executing a cmd,
then goes OFF.

Off

The UI LED should be off, unless active.

UI Cmd

Off

Normally off.

Green/blinking

The UI Cmd LED blinks once each time the UI
Set button is pressed, and while the UI LED is
blinking.

Pwr Green

Power

on.

Off

Unit not connected to a power source.

Set

T: 1000T

A: Activity

LED Status

Amber:10Mps

Green:100

Mps Blink:Activity

Cmd

Pwr

LED Status

Off:Hal

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 60 / 488

Результаты поиска

Содержание 425-24T

Отзывы: