manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 136 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 136

136

Chapter 3 CLI Basics

320985-A Rev 01

 

Table 23

 describes the parameters and variables for the 

shutdown

 command.

The 

shutdown

 command is in the privExec command mode.

reload command

The 

reload 

command provides you with a configuration rollback mechanism to 

prevent loss of connectivity to a switch, typically for remote configurations. The 

reload

 command allows you to temporarily disable the autosave feature for a 

specified time period (1 to 60 minutes), allowing you to make a number of 
configuration changes on remote switches without affecting the current saved 
configuration. During the interval in which the autosave feature is disabled by the 

reload

 command, you must use the 

copy config nvram

 command to force a 

manual save of your configurations. 

Initiate the 

reload

 command before you start the switch configuration 

commands. Once you initiate the command in the CLI, the following message 
appears:

Reload (y/n) ? 

Enter yes at this prompt to set the switch reload. 
The following warning message then appears:

Table 24   

shutdown command parameters and variables

Parameters 
and variables

Description

force

Instructs the switch to skip the shutdown confirmation prompt.

minutes-to-wait 
<1-60>]

Specifies the number of minutes that pass before the switch resets 
itself. The default wait time is set at 10 minutes.

cancel

Aborts all scheduled switch shutdowns

Note: 

Any configurations or logins performed on the switch after the 

shutdown command is initiated are not saved to NVRAM and are lost 
after the reset.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов