Nortel 425-24T Скачать руководство пользователя страница 133

Страница: 133 / 488

Chapter 3 CLI Basics

133

System Configuration Guide

Table 22

describes the parameters and variables for the

configure

command.

interface command

The

interface

command moves you to the Interface Configuration (config-if)

command mode. The syntax for the

interface

command is:

interface FastEthernet <portlist>

The

interface

command is in the config command mode.

Table 23

describes the parameters and variables for the

interface

command.

disable command

The

disable

command returns you to the User EXEC (exec) command mode.

The syntax for the

disable

command is:

disable

The

disable

command is in the privExec command mode.

The

disable

command has no parameters or variables.

Table 22

configure command parameters and variables

Parameters and
variables

Description

terminal | network

Specifies the source for the configuration commands for the Ethernet Switch
325/425:

terminal—allows you to enter config mode to enter configuration commands

network—allows you to set up parameters for auto-loading a script at boot-up
or for loading and executing a script immediately

Table 23

interface command parameters and variables

Parameters
and variables

Description

Specifies the portlist you want to be affected by all the commands
issued in the config-if command mode.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 133 / 488

Результаты поиска

Содержание 425-24T

Отзывы: