manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 310 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 310

310

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Table 102

 describes the parameters and variables for the 

show lldp port

 

command. 

Figure 116

 displays the output from the

 show lldp port neighbor 

command.

Figure 116   

show lldp port neighbor command output

Table 103   

show lldp port command parameters and variables

Parameters and 
variables

Description

port 

<portlist>

Specifies the ports affected by the command.

neighbor

Displays LLDP neighbors.

neighbor-mgmt-addr Displays LLDP management addresses for neighbors.

rx-stats

Displays LLDP receive statistics.

tx-stats

Displays LLDP transmit statistics.

tx-tlv

Displays LLDP transmit TLVs.

425>show lldp port 1/1 neighbor

------------------------------------------------------------------------

                            lldp neighbor

------------------------------------------------------------------------

------------------------------------------------------------------------

Port   Time  Index  ChassisIdSubtype  ChassisId SysCap Supported  Enabled

------------------------------------------------------------------------

SysName             PortIdSubtype     PortId            PortDesc

------------------------------------------------------------------------

SysDesc

------------------------------------------------------------------------

3/1       78      1  MAC address     00:09:68:b2:9d:60        B        B

425 stacks v360      MAC address     00:09:68:b2:9d:82  port24

Ethernet Switch 425-24T  HW:0B       FW:3.5.0.2   SW:v3.6.0

------------------------------------------------------------------------

Sys capability: O-Other; R-Repeater; B-Bridge; W-WLAN accesspoint; 

r-Router; T-Telephone; D-DOCSIS cable device; S-Station only.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов